Arkadaşlar araçtaki lpg yi digital ortama dökmek istiyorum kullandığım malzemeler aşağıdaki gibidir arduino uno potansiyometre hc05 bluetooth modülü yada esp potansiyo metre yerine hall sensörümü kullansam daha iyi olur… arkadaslar google playdaki virtiuno programınıda kullanarak lpgdeki verileri senkron ederek digital ortama aktardım fakat arduinoda sadece virtuino kutuphanesi ve bluetooth modül bağlantısı için kodlar mevcut gerisini virtiuno hallediyor benim istediğim en alttaki kodlarla üsteki kodları virtiuno görecek şekilde yapılandırılması lazım en alttaki kodlar lcd panelde gösterim için yazılmış kod bunu virtiuno görecek şekilde nasıl yarlayabilirim… include <softwareserial.h>
SoftwareSerial espSerial = SoftwareSerial(9,10); // arduino RX pin=2 arduino TX pin=3 connect the arduino RX pin to esp8266 module TX pin - connect the arduino TX pin to esp8266 module RX pin
include “VirtuinoEsp8266_WebServer.h”
VirtuinoEsp8266_WebServer virtuino(espSerial); // Your esp8266 device’s speed is probably at 115200. For this reason use the test code to change the baud rate to 9600
include <onewire.h>
include <dallastemperature.h>
define ONE_WIRE_BUS 8 // Connect one, two or more ds18b20 sensors to pin 6
OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature sensors(&oneWire);
void setup()
{
virtuino.DEBUG=true; // set this value TRUE to enable the serial monitor status.It is neccesary to get your esp8266 local ip
Serial.begin(9600); // Enable this line only if DEBUG=true
espSerial.begin(9600); // Disable this line if you want to use software serial (Mega, DUE etc.)
virtuino.createLocalESP8266_wifiServer(“SMART ALBEA”,“5525967aa”,80,2); //Enable this line to create a wifi local netrork using ESP8266 as access point
virtuino.password=“1234”;
sensors.begin(); // Start up the library Dallas Temperature IC Control Library
}
void readTemperatureFormDS18B20(){
sensors.requestTemperatures(); // Send the command to get temperatures
float temperature0=sensors.getTempCByIndex(0); // 0 refers to the first IC on the wire
float temperature1=sensors.getTempCByIndex(1); // 0 refers to the first IC on the wire
float temperature2=sensors.getTempCByIndex(2); // 0 refers to the first IC on the wire
virtuino.vMemoryWrite(0,temperature0); // write temperature to virtual pin V2. On Virtuino panel add a value display or an analog instrument to pin V2
virtuino.vMemoryWrite(1,temperature1); // write temperature to virtual pin V2. On Virtuino panel add a value display or an analog instrument to pin V2
virtuino.vMemoryWrite(2,temperature2); // write temperature to virtual pin V2. On Virtuino panel add a value display or an analog instrument to pin V2
}
void loop(){
virtuino.run(); // neccesary command to communicate with Virtuino android app
readTemperatureFormDS18B20(); // Dont’ read the sensors values every cycle
virtuino.vDelay(500);
}
---------------------------------LCD PANEL KOD VİRTUİNO GÖRMÜYOR----------------------------
include <liquidcrystal_i2c_avri2c.h>
LiquidCrystal_I2C_AvrI2C lcd(0x3F,20,4); // 16 karakter 2 satır için - 20x4 satır için (0x27,20,4) yazın
int offset =20;// set the correction offset value
void setup()
{
lcd.begin();
lcd.setCursor(19,1);
lcd.print(“V”);
}
void loop() {
int volt = analogRead(A0);// read the input
double voltage = map(volt,0,1023, 0, 2500) + offset;// map 0-1023 to 0-2500 and add correction offset
voltage /=100;// divide by 100 to get the decimal values
lcd.setCursor(11,1);
lcd.print(“AKU:”);
lcd.print(voltage,1);//print the voltge
delay(1000);
}
</liquidcrystal_i2c_avri2c.h></dallastemperature.h></onewire.h></softwareserial.h>